Aansluit- en montageonderdelen
Bekijk de productgroepen voor je installatie. De juiste uitvoering hangt af van je paneel en installatie.
Alle aansluit- en montageonderdelen →Hulp bij een compleet systeem? Vergelijk de systemen of bekijk persoonlijk advies.
Victron Energy
Victron BlueSolar 345W monocrystalline solar panel
Victron BlueSolar 345W monocrystalline solar panel
Couldn't load pickup availability
Niet op voorraad in Raalte; afhalen kan na bestelling. Bestel vooraf; we laten weten zodra het klaarligt.
The Victron BlueSolar 345Wp monocrystalline solar panel is a robust glass panel for campers, boats and other off-grid installations. The anodized aluminum frame, tempered glass and bypass diodes make it suitable for fixed mounting in a variety of conditions.
- 345Wp rated power
- Monocrystalline solar cells
- Dimensions: 1870 × 880 × 35 mm
- Weight: 17.28 kg
Pick up or have it delivered directly
Due to its large size, this solar panel is not shipped as a standard parcel. You can pick it up free of charge from our supplier in Grou after confirmation. Direct pallet delivery to a Dutch address is available for €49.95. Availability and the pick-up or delivery time will be confirmed after ordering. Any accessories may be delivered separately.
Why this Victron BlueSolar panel?▾
- Good performance in low light and sensitivity across a wide light spectrum.
- Waterproof junction box and bypass diodes to limit power loss due to partial shading.
- Sturdy aluminum frame and tempered glass for fixed mounting.
- Fits well in an installation with a Victron MPPT charge controller and VictronConnect.
The actual yield depends on the season, solar radiation, shading, mounting orientation and the battery state of charge.
Specifications and dimensions▾
345Wp
Monocrystalline
38.7V
8.8A
45.2V
9.27A
1870 × 880 × 35 mm
17.28 kg
What do you need with it?▾
- Charge controller: Victron SmartSolar MPPT 100/30 for one panel on a 12V battery installation.
- Solar cable: 6mm², 2 × 5m with connectors.
- Battery cable and fuse: 10mm² battery cable + 40A MIDI fuse + MIDI fuse holder, with the fuse close to the battery or positive busbar.
- Roof penetration: choose a suitable roof penetration for the cable route inside.
- Cable management: use UV- and weather-resistant adhesive cable mounts and zip ties.
Never connect a solar panel directly to the battery. Always use a correctly sized charge controller and protection.
Mounting on camper, boat or frame▾
Van conversion: preferably use aluminum Z-profiles on a corrugated or slightly curved metal roof.
Boat: plastic corner brackets are a practical choice on a suitable flat deck.
Flat camper roof or other construction: for this panel width, no suitable spoiler wider than 68 cm is available. Therefore, mount the panel with Z-profiles or corner brackets, or on a suitable frame or rack.
Measure the available space beforehand and take skylights, ventilation, rails and mounting material into account. Carefully degrease the surface, use suitable construction adhesive and primers and seal all penetrations watertight.
Use with a 24V battery▾
The higher panel voltage may be suitable for 24V; always check MPPT settings, temperature margin and system configuration.
In a 24V system, the same MPPT can handle approximately twice as much solar panel power as in 12V, but only when the panel voltage, maximum open-circuit voltage and wiring are suitable.
Common mistakes▾
- Connecting the panel directly to the battery.
- Only paying attention to wattage and forgetting the panel voltage or Voc.
- Using a cable that is too thin or omitting a fuse.
- Combining panels with different electrical characteristics without checking.
- Not taking shading, roof obstacles and mounting space into account.
Deel
